Connect with us :
Register
Steel Composition: Elements, Grades and How to Choose
Ramesh · · 8 min read

Steel Composition: Elements, Grades & Uses

Steel composition is the list of elements inside the metal and how much of each is present, and it decides almost everything a buyer cares about: strength, hardness, weldability, corrosion resistance and price. Two bars that look identical can behave very differently on a fabrication floor because one carries 0.20% carbon and the other 0.45%.

Here is what steel is made of, what each element does, how the main families differ, and how to read a mill test certificate before you order. If you buy or sell steel on a marketplace such as Lohaa, the same chemistry applies to every listing.

What is steel made of?

Steel is an alloy of iron and carbon, with carbon up to about 2.14% by weight. Above that level the material is classed as cast iron, which is harder but more brittle. Plain carbon steel is usually more than 98% iron, and the small remainder is what sets one grade apart from another.

That remainder comes from two places. Some elements are added on purpose, such as manganese, chromium, nickel and molybdenum, and these are called alloying elements. Others are left over from ore, scrap and the furnace, such as sulphur and phosphorus, and mills work to keep them low.

Carbon is the first thing to check. Steels are commonly grouped as low carbon (below 0.25% C), medium carbon (0.25% to 0.55%) and high carbon (above 0.55%). More carbon means more strength and hardness, but less ductility and harder welding.

Main alloying elements and what they do

The ranges below are typical values, not limits for any single grade. Always confirm against the standard you are buying to.

Element

Typical range

What it does

Trade-off

Carbon (C)

0.05% to 1.0%+

Raises strength and hardness

Lowers ductility and weldability

Manganese (Mn)

0.3% to 1.5% (11% to 14% in Hadfield steel)

Deoxidises, offsets sulphur brittleness, improves hardenability

Too much with high carbon causes brittleness

Silicon (Si)

0.1% to 0.5% (up to about 3% in electrical steel)

Deoxidises, adds strength

Can reduce toughness in excess

Chromium (Cr)

0.5% to 1.5% in alloy steel, above 10.5% in stainless

Hardness, wear and corrosion resistance

Cost, harder machining

Nickel (Ni)

0.3% to 5% in alloy steel, 8% to 10.5% in 304

Toughness, especially at low temperature

High price

Molybdenum (Mo)

0.15% to 1%

Strength at high temperature, hardenability, pitting resistance

Cost

Vanadium (V)

0.05% to 0.2%

Refines grain, adds strength and wear resistance

Cost

Copper (Cu)

0.2% to 0.5%

Atmospheric corrosion resistance (weathering steel)

Can cause hot cracking if uncontrolled

Types of steel by composition

Carbon steel

Carbon steel relies mainly on carbon and manganese. Low carbon (mild) steel is easy to weld and form, so it dominates construction, TMT bars and sheet. Medium carbon steel suits shafts, axles and gears. High carbon steel holds an edge and is used for springs, wire and cutting tools. For the trade-offs in more detail, see the pros and cons of carbon steel.

Alloy steel

Alloy steels add elements such as chromium, nickel and molybdenum for strength, toughness or heat resistance. Low alloy steel has less than 5% total alloying elements, and high alloy steel has more than 5%. Chromium-molybdenum grades are common in pressure vessels, crankshafts and heavy machinery. Lohaa's guide to different types of metal alloys and their industrial applications covers more families.

Stainless steel

Stainless steel contains at least 10.5% chromium, which forms a thin protective oxide layer on the surface. The familiar 18-8 type holds about 18% chromium and 8% nickel. Adding molybdenum, as in grade 316, improves resistance to chlorides, which matters near the coast and in chemical plants. For a side-by-side view, read carbon steel vs stainless steel. For how nickel and chromium costs feed into prices, see stainless steel prices and alloy trends.

Tool steel

Tool steels combine high carbon with tungsten, molybdenum, vanadium and chromium to stay hard under heat and wear. They are used for dies, punches and cutting tools, and they cost far more per tonne than structural steel.

Common steel grades and their chemistry

Values are approximate weight percentages. Check the current standard or your supplier's data sheet before you order.

Grade

Type

Carbon

Manganese

Chromium

Nickel

Other

Typical use

IS 2062 E250

Mild structural

up to 0.23%

up to 1.5%

none

none

S, P up to 0.045%

Beams, plates, fabrication

AISI 1045

Medium carbon

0.43% to 0.50%

0.60% to 0.90%

none

none

 

Shafts, bolts, gears

AISI 1095

High carbon

0.90% to 1.03%

0.30% to 0.50%

none

none

 

Springs, blades

AISI 4140

Cr-Mo alloy

0.38% to 0.43%

0.75% to 1.00%

0.80% to 1.10%

none

Mo 0.15% to 0.25%

Crankshafts, tooling

AISI 304

Austenitic stainless

up to 0.08%

up to 2.0%

18% to 20%

8% to 10.5%

 

Kitchen, food, general use

AISI 316

Austenitic stainless

up to 0.08%

up to 2.0%

16% to 18%

10% to 14%

Mo 2% to 3%

Marine, chemical

Impurities: sulphur and phosphorus

Sulphur and phosphorus are the two residuals buyers should watch. Sulphur forms iron sulphide at grain boundaries, which makes steel crack during hot rolling and forging. Phosphorus raises strength slightly but cuts ductility and impact toughness, especially in the cold.

Most structural and engineering grades cap each of them at roughly 0.04% to 0.05%. Free-machining steels are the exception, because added sulphur helps chips break cleanly, but they are a poor choice for welded or load-bearing parts. Manganese helps here too, since it ties up sulphur as manganese sulphide instead of brittle iron sulphide.

How to read a mill test certificate and pick the right composition

A mill test certificate (MTC) is the proof of what you are actually getting. Check four things before you accept a lot:

  1. Heat number: it must match the number stamped or tagged on the material.
  2. Standard and grade: for example IS 2062 E250 or ASTM A36, matching your purchase order.
  3. Chemical analysis: each element reported against the limit in the standard, with sulphur and phosphorus at the low end.
  4. Mechanical results: yield strength, tensile strength and elongation, which confirm the chemistry produced the right properties.

If you weld the material, also look at carbon equivalent, which estimates how hard the steel will get next to a weld. A common formula is:

CE = C + \frac{Mn}{6} + \frac{Cr + Mo + V}{5} + \frac{Ni + Cu}{15}

Lower values weld more easily. As a rough guide, many fabricators want to stay below about 0.40 for routine welding without preheat, but follow the welding procedure for your project.

Start from the job. Low carbon gives the best weldability at the lowest cost. Higher carbon or a tool grade suits wear and edge retention. Stainless handles corrosion, with the grade matched to the environment. For toughness under load or in the cold, look at nickel or chromium-molybdenum alloys.

Buying and selling steel on Lohaa

Knowing the chemistry only helps if the material you receive matches it. Lohaa is a B2B marketplace where buyers and sellers of ferrous and non-ferrous metals, alloys, ores and machinery trade, with daily metal prices and industry news alongside the listings.

When you list or enquire about steel on Lohaa, state the grade, the standard and the required chemical range up front, and ask for the mill test certificate before you confirm. If the material is questioned later, buyer and seller are then working from the same numbers.

FAQs on steel composition

What is the chemical composition of steel?

Steel is mainly iron with up to about 2.14% carbon, plus controlled amounts of manganese, silicon and, depending on the grade, chromium, nickel, molybdenum or vanadium.

What is the difference between carbon steel and stainless steel composition?

Carbon steel gets its properties from carbon and manganese and rusts in moist air. Stainless steel has at least 10.5% chromium, which forms a protective surface layer. Our steel vs stainless steel explainer covers the basics.

Which element has the biggest effect on steel?

Carbon. Small changes of a tenth of a percent shift hardness, strength and weldability noticeably, which is why it is the first number to check.

How do I verify steel composition?

Ask for the mill test certificate and match the heat number to the material. For added certainty, a third-party lab or a spectrometer (OES) test on a sample gives an independent analysis.

Why are sulphur and phosphorus limited?

They make steel brittle, sulphur when hot and phosphorus when cold, so most structural grades cap each at about 0.04% to 0.05%.

Conclusion

Steel composition comes down to a few numbers: carbon for strength, manganese and silicon for processing, chromium and nickel for corrosion and toughness, and low sulphur and phosphorus for reliability. Match those numbers to the job, and confirm them with a mill test certificate.

Ready to buy or sell steel? register on Lohaa, and find more on the Lohaa blog.

Related reading

Sources

Trade metals on LOHAA

Post offers and requirements, follow metal prices and connect with buyers and sellers.

Join LOHAA
Steel Composition: Elements, Grades and How to Choose

Steel Composition: Elements, Grades and How to Choose

Learn how carbon, manganese, chromium and nickel shape steel composition, compare common grades, and read a mill test certificate before you buy.